How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models has the keyless entry feature built into. This key is similar to a remote control, and is exchangeable by an Kia dealer.
Key fobs may stop working due to a variety of reasons, including batteries that are dead worn buttons signals, water damage, signal interference, and a defective receiver module. Here are some tips on how to get your Kia Sportage replacement key to function again.
How do you replace the remote key or the smart key?
our homepage in your Kia's intelligent key will eventually need be replaced, regardless of whether it's a remote key, a push-to-start key or a regular metal key that doesn't have a transponder. This is especially in the event that your vehicle displays a message that indicates that the smart key or remote is not powered by the battery.
Luckily, this is a relatively simple process. In order to replace the battery on the key fob remove the mechanical key from the slit at the back of the key fob and lift the cover. Inside the key fob, there will be tiny screws that hold the battery in its place. Utilizing a small screwdriver unscrew the screw and pull out the battery that was in place. Then, insert the new and close the slit in the key fob.
Test the key fob by pressing the lock and unlock buttons. You're good to go in case the doors lock and unlock as you expect. You can now make use of the hands-free lock/unlock feature on your Kia whenever your fingers get chilly or you have to run some errands in Brandon.
Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a machine for programming which is available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, it is necessary to write down the key code's number on the key code tag.
How do you replace the battery?
If the Kia key fob is unable to respond when you press the lock/unlock button, it's a sign that the battery is insufficient. A low battery could cause other issues, such as the check engine light turning on or the engine not cranking. It is quite simple to replace key fob batteries using just some tools.
Before you begin the process ensure that your vehicle is off and all doors are shut. Locate the small plastic piece that is on the bottom of your key fob and play with it until a metallic key slides out. Then, you can insert this key into the handle on the door of your driver to open your car.
To replace the key fob battery, remove the cover at the rear and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery, and then align the new battery to ensure that the "+" positive side faces your face and the "negative" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or bending the contacts on the metal.
After installing the new battery and turning the key fob on and off in the ignition until the door locks up. You can then test your Kia's key fob once more to ensure it's working properly.
How can you replace the smart key
Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference between these is that the smart key has an incredibly small key blade tucked inside it, while the standard fob doesn't. Both key fobs are equipped with a battery that will eventually need to be changed. This is a simple procedure that takes only two minutes.
Before you start, you will want to make sure that you are on a flat surface with enough lighting and that your Kia is not on. Also, keep in mind that there are tiny components inside the fob which could be snagged if not careful.
The first step is to locate the small release button that is located on the lower backside of your fob. This will be either a circular button or a rectangular slot. After pressing this button mechanical key blade, it will pop out and you will be able to open the key fob.
Once the key fob is removed, you can remove the battery that was in it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished, you should be able to lock or unlock your vehicle with your key fob - even if your engine isn't running!
How do you replace a mechanical key
The Kia key fob is a great convenience that allows us to lock and unlock our vehicle with the push of an button. Like any device it is possible that the Kia key fob might have issues. There are solutions to solve these issues and keep your key fobs functioning for many years.
One of the most frequent issues is a low or dead battery. This could cause the fob to stop working completely or stop working at times. If this is the case try replacing the battery with a fresh new one.
If this isn't enough to solve the issue, use a standard flathead screwdriver to wedge the plastic casing of the fob open. Be cautious not to damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.
After the new battery has been put in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that can fit in the slot). Test the key fob to verify that it's functioning correctly. If the device not working, contact a dealer or locksmith to resolve the issue. To avoid locking outs in the future, make sure you get an emergency key that will be able to work with all door and trunk cylinders.